Serving Arizona Statewide
Seismic Engineer in Arizona
ASCE 7-22 nonstructural anchorage, special seismic certification, and AC156 shake table testing — for Phoenix, Tucson, Mesa, Flagstaff, and statewide hospitals, data centers, labs, and critical facilities. Stamped by licensed PE/SE engineers.
Licensed Seismic & Structural Engineers for Arizona Projects
Panache Engineering delivers PE-stamped nonstructural seismic engineering for Arizona projects — semiconductor fabs, data centers, hospitals, and industrial plants. Arizona adopts the IBC locally, and ASCE 7 Chapter 13 anchorage documentation is routinely required for Risk Category III and IV facilities and for any component with Ip = 1.5, even where the site Sds is comparatively low.
PE/SE-stamped seismic anchorage calculations to ASCE 7-22 Chapter 13 for mechanical, electrical, and plumbing equipment installed at Arizona hospitals, labs, data centers, and critical facilities. Submittals formatted for Phoenix and Tucson and statewide plan check.
IBC §1705.13 / ASCE 7-22 §13.2.2 special seismic certification for equipment and components that must remain operational after a design earthquake — by analysis, by test, or by experience data.
Test plan development, AC156 required response spectrum (RRS) derivation, and witness/peer review at independent labs. Reports formatted for IBC special seismic certification submittals nationwide.
Seismic bracing layouts for piping, ductwork, conduit, and cable tray per NFPA 13 and SMACNA, plus FEMA E-74 nonstructural risk walkthroughs and prioritized mitigation reports for existing facilities.
Built for Arizona Code Authorities & Project Types
Code authorities we work with
- • City of Phoenix Planning & Development Department
- • City of Tucson / Pima County Development Services
- • Maricopa County Planning & Development
- • Arizona Department of Health Services (healthcare licensure)
- • City of Flagstaff and Coconino County (higher seismic demand)
Typical Arizona project types
- • Semiconductor fab process, tool, and utility equipment anchorage
- • Phoenix-metro data center switchgear, UPS, battery, and cooling anchorage
- • Hospital and outpatient MEP equipment anchorage and certification
- • Mining and industrial plant non-building structure design (ASCE 7 Ch. 15)
- • Rooftop unit, generator, and tank anchorage
- • Sprinkler and duct seismic bracing per NFPA 13 and SMACNA
Frequently Asked Questions — Arizona Seismic Engineering
Does Arizona require seismic anchorage calculations?+
Yes, where the adopted IBC requires them. Arizona jurisdictions adopt the IBC locally, and ASCE 7 Chapter 13 exempts only a narrow set of light or low-consequence components. Equipment in Risk Category III and IV buildings, components with Ip = 1.5, and most rooftop and floor-mounted mechanical equipment need engineered anchorage with a PE stamp.
Which seismic design category applies in Phoenix?+
Most Phoenix-area sites fall in Seismic Design Category B, with parts of northern Arizona around Flagstaff notably higher. Even in SDC B, components assigned Ip = 1.5 and equipment in essential facilities still need anchorage designed and documented per ASCE 7 Chapter 13.
Do you support semiconductor fab equipment anchorage?+
Yes. We design anchorage for process tools, gas cabinets, abatement equipment, chillers, AHUs, and utility skids, including waffle-slab and raised-floor conditions, and we coordinate with tool vendors on attachment points and allowable base reactions.
Can you handle wind design as well as seismic?+
Yes. For Arizona rooftop equipment, screens, and non-building structures, wind loads per ASCE 7 Chapter 29 often govern over seismic. We evaluate both load cases and report the governing condition in the same stamped package.
How do I get a quote for an Arizona project?+
Send equipment cut sheets with weights and center of gravity, the mounting substrate, the mounting height in the structure, and the project Sds and Ip. We return a written scope, fee, and schedule — typically within one business day.
Ready to talk about your Arizona project?
Send us your equipment cut sheets, project location, and required SDS / Ip. You'll get a scope, fee, and schedule from a licensed engineer — typically within one business day.
Office: 150 N Santa Anita Ave, Arcadia, CA 91006 · (626) 698-0784
Seismic anchoring services · AC156 shake table testing · All services