Serving New York Statewide
Seismic Engineer in New York
ASCE 7-22 nonstructural anchorage, special seismic certification, and AC156 shake table testing — for New York City, Long Island, Westchester, Albany, Buffalo, and statewide hospitals, data centers, labs, and critical facilities. Stamped by licensed PE/SE engineers.
Licensed Seismic & Structural Engineers for New York Projects
New York projects carry real nonstructural seismic requirements even though the region is moderate-seismic: the NYC Building Code and the NYS Uniform Code both reference ASCE 7 Chapter 13 for equipment anchorage, and NYC DOB reviewers expect stamped calculations for mechanical equipment, generators, tanks, and rooftop units. Panache Engineering produces those packages, plus IBC §1705.13 special seismic certification for equipment that must stay operational.
PE/SE-stamped seismic anchorage calculations to ASCE 7-22 Chapter 13 for mechanical, electrical, and plumbing equipment installed at New York hospitals, labs, data centers, and critical facilities. Submittals formatted for NYC DOB and statewide plan check.
IBC §1705.13 / ASCE 7-22 §13.2.2 special seismic certification for equipment and components that must remain operational after a design earthquake — by analysis, by test, or by experience data.
Test plan development, AC156 required response spectrum (RRS) derivation, and witness/peer review at independent labs. Reports formatted for IBC special seismic certification submittals nationwide.
Seismic bracing layouts for piping, ductwork, conduit, and cable tray per NFPA 13 and SMACNA, plus FEMA E-74 nonstructural risk walkthroughs and prioritized mitigation reports for existing facilities.
Built for New York Code Authorities & Project Types
Code authorities we work with
- • NYC Department of Buildings (DOB) — NYC Building Code Chapter 16
- • New York State Uniform Fire Prevention and Building Code
- • NYS Department of Health (Article 28 healthcare facilities)
- • Port Authority and agency-specific design standards
- • Local building departments in Westchester, Nassau, Suffolk, and upstate cities
Typical New York project types
- • High-rise mechanical room and rooftop equipment anchorage
- • Hospital and Article 28 facility MEP anchorage and certification
- • Data center and colocation UPS, battery, and switchgear anchorage
- • Cogeneration, generator, and fuel oil tank anchorage
- • Tenant improvement equipment restraints and vibration isolation with snubbers
- • Sprinkler, piping, and duct seismic bracing per NFPA 13 and SMACNA
Frequently Asked Questions — New York Seismic Engineering
Does NYC require seismic anchorage for mechanical equipment?+
Yes. The NYC Building Code adopts ASCE 7 with NYC amendments, and Chapter 13 nonstructural provisions apply to mechanical, electrical, and plumbing components. DOB plan examiners commonly ask for stamped seismic anchorage calculations for rooftop units, generators, tanks, pumps, and switchgear, especially in Risk Category III and IV buildings.
How does high mounting elevation affect anchorage in NYC towers?+
Strongly. ASCE 7-22 amplifies component demand with height through the Hf factor, so equipment on the mechanical floor of a tall building can see several times the Fp of the same unit at grade. We compute Hf explicitly using the component's mounting elevation and the structure height rather than assuming a worst case.
Do you provide vibration isolation and snubber design?+
Yes. Isolated equipment is a frequent New York condition, and ASCE 7 requires the isolated case to be checked with the appropriate amplification and snubber capacity. We size restrained spring isolators and snubbers and verify the attachment to the supporting structure.
Can you stamp for New York State?+
We work with licensed New York professional engineers to seal deliverables that require an NY stamp. Tell us the jurisdiction and submittal type up front and we will confirm the stamping arrangement in writing before work starts.
What is your turnaround for a New York submittal?+
Typical equipment anchorage packages take 5–10 business days, and DOB comment responses are usually turned around in 2–3 business days. Send cut sheets, the structural substrate, mounting elevation, and the project Ss/S1 or Sds and Ip for a same-day-to-next-day quote.
Ready to talk about your New York project?
Send us your equipment cut sheets, project location, and required SDS / Ip. You'll get a scope, fee, and schedule from a licensed engineer — typically within one business day.
Office: 150 N Santa Anita Ave, Arcadia, CA 91006 · (626) 698-0784
Seismic anchoring services · AC156 shake table testing · All services